Xerox DocuPrint N4525 Скачать руководство пользователя страница 192

Страница: 192 / 380

1-170

DocuPrint N4525 Network Laser Printer - Service Guide

Press [2] or [6] to
display:

Press [3] or [7] to
display:

Action To Take

Displayed Result

Finisher Unit
Low Stpl Switch

1. Press [4] to begin test.
2. Actuate Low Staple Switch

Sensor.

3. Press [0] to end test.

With Pin
Without Pin

Finisher Unit
Stpl Cart Switch

1. Press [4] to begin test.
2. Actuate Staple Cartridge

Switch Sensor.

3. Press [0] to end test.

With Cartridge
Without Cartridge

Finisher Unit
Stpl Cam HP

1. Press [4] to begin test.
2. Actuate Staple Cam Home

Position Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Stpl Ready Sen.

1. Press [4] to begin test.
2. Actuate Staple Ready

Sensor.

3. Press [0] to end test.

Without Pin Pos
With Pin Pos

Finisher Unit
Stker Tray Paper

1. Press [4] to begin test.
2. Actuate Stacker Bin Paper

Sensor.

3. Press [0] to end test.

With Paper

Finisher Unit
Stk Hight Sen Lw

1. Press [4] to begin test.
2. Actuate Stacker Height Low

Sensor.

3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Stk Hight Sen Up

1. Press [4] to begin test.
2. Actuate Stacker Height Up

Sensor.

3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Stker Upper Limit

1. Press [4] to begin test.
2. Actuate Stacker Upper Limit

Sensor.

3. Press [0] to end test.

Off Position
On Position

Finisher Unit
Stker Lower Lmt

1. Press [4] to begin test.
2. Actuate Stacker Lower Limit

Sensor.

3. Press [0] to end test.

Off Position
On Position

Finisher Unit
Stker Position

1. Press [4] to begin test.
2. Actuate Stacker Position

Sensor.

3. Press [0] to end test.

Not Pass Slit
Pass Slit

Finisher Unit
Docking Lock

1. Press [4] to begin test.
2. Actuate Docking Lock

Sensor.

3. Press [0] to end test.

Docked
Not Docked

Finisher Unit
Exit Roller Lock

1. Press [4] to begin test.
2. Actuate Exit Roller Lock

Sensor.

3. Press [0] to end test.

Out of Range
In Range

Finisher Unit
Front Cover Lock

1. Press [4] to begin test.
2. Actuate Front Cover Lock

Sensor.

3. Press [0] to end test.

Close
Open

Finisher Unit
Punch Dust Box

1. Press [4] to begin test.
2. Remove Punch Dust Box/

Reinstall.

3. Press [0] to end test.

Without Box
With Box

Table 1-106 Component Control Input Tests

Press [1] or [5] until to display:

Main Menu
Comp Input Test (cont'd.)

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды