Xerox DocuPrint N4525 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 102

1-

80

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-29

Error Code E5-2

Close Door B

The Left Lower Cover (B) is open.

The Left Lower Cover (B) is closed, but Logic Control on the Print Engine Controller

Board sensed the Left Lower Cover Interlock Switch is open.

Table 1-57 Error Code E5-2 Close Door B

Step

Actions and Questions

Yes

No

1

LEFT LOWER COVER CHECK

Open and close the Left Lower Cover (B).

Is the error code cleared?

Problem
solved

Go to step 2

2

LEFT LOWER COVER INTERLOCK SWITCH
INSPECTION

Inspect the Left Lower Cover Interlock Switch for
damage.

Is the switch damaged?

Replace the
Left Lower
Cover
Interlock
Switch

Go to step 3

3

LEFT LOWER COVER INTERLOCK ACTUATOR
INSPECTION

Inspect the Left Lower Cover (B) Interlock Actuator for
damage that may prevent the Cover from actuating the
Interlock when the Cover is closed.

Is the Interlock Actuator damaged?

Replace the
Left Lower
Cover

Go to step 4

4

LEFT LOWER COVER INTERLOCK SWITCH
TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / Tray 1

Cover (B).

3. Actuate and deactuate the Left Lower Cover (B)

Interlock Switch.

Does the display indicate Open/Closed when
you actuate and deactuate the Lower Left
Cover Interlock Switch?

Replace the
Left Lower
Cover
Interlock
Switch

Go to step 5

5

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 6

Problem
solved

6

The following printer components and areas are
associated with this specific problem. One or more of
these components or areas may have failed partially or
completely. If you cannot isolate this problem using the
steps in this Repair Analysis Procedure, replace each
component or troubleshoot each area listed below, one at
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

«
...
100
101
102
103
104
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды