Xerox DocuPrint N4525 Скачать руководство пользователя страница 46

Страница: 46 / 380

1-24

DocuPrint N4525 Network Laser Printer - Service Guide

Print Media, continued

Table 1-19 Supported Media and Media Sizes

Media

Media Size

Tray 1 Tray 2

Tray 3

Tray 4
Tray 5

Custom

Paper

Tray

Multi-
sheet

Bypass

Feeder

Envelope

Feeder

(2)

297 x 420 mm

•

(1)

210 x 297 mm

•

(1)

148 x 210 mm

•

(6)

•

(1)

105 x 148 mm

•

Statement

(1)

5.5 x 8.5 in.

•

(6)

•

B5-JIS

(1)

182 x 257 mm

•

B4-JIS

(2)

257 x 364 mm

•

Executive

(1)

7.25 x 10.5 in.

•

Letter

(1)

8.5 x 11 in.

•

Folio

(2)

8.5 x 13 in.

•

Legal

(2)

8.5 x 14 in.

•

Ledger

(2)

11 x 17 in.

•

Envelopes

COM-10

(1) (4)

Monarch

(1) (4)

4.1 x 9.5 in.

3.8 x 7.5 in.
110 x 220 mm

162 x 229 mm

•

•
•

•

•
•

•

Transparencies

(1) (4)

Letter

(1) (4)

210 x 297 mm
8.5 x 11 in.

•
•

Labels

(1) (4)

Letter

(1) (4)

210 x 297 mm

8.5 x 11 in.

•

(5)

•

Custom Sizes

(3)

•

(1)

Use long-edge feed.

(2)

Use short-edge feed.

(3)

Custom Sizes — see the following page for the range of acceptable sizes.

(4)

Envelopes, transparencies, labels, and custom sizes cannot be printed in duplex mode.

(5)

Tray 4 only

(6)

Not available if Custom Paper Tray is used in Tray 2 or 3 position.

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды