Xerox DocuPrint N4525 Скачать руководство пользователя страница 157

Страница: 157 / 380

Volume 1 / Print Engine - Troubleshooting

135

RAP 1-71

Toner on Back of Print

PROBLEM

There is toner contamination on the back of the fused sheet of
paper.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-26 Toner on Back of Print

Table 1-95 Toner on Back of Print

Step

Actions and Questions

Yes

PAPER JAM HISTORY

Frequently a paper jam or clearing a paper jam may
result in some minor toner contamination of the paper
path.

Did you just clear a paper jam?

Run 30 Test
Prints to clear
the paper
path of
residual toner

Go to step 2

PAPER Tray INSPECTION

Inspect all of the paper Bins for loose toner on top of and
under the paper stack.

Is there toner in any of the paper Bins?

Clean the
Bins and
replace all of
the paper with
new paper

Go to step 3

PAPER PATH INSPECTION

1. Remove the paper Bins.
2. Remove the Laser Print (EP) Cartridge.
3. Use a flashlight to inspect the entire paper path, from

Feeder to Output Bin, for any loose toner.

Is the paper path free of loose toner?

Go to step 4

Thoroughly
clean the
paper path,
from Feeders
to the Output
Bin, including
all rubber
feed Rollers

BIAS TRANSFER ROLLER INSPECTION

Rotate and inspect the Bias Transfer Roller.

Is the Bias Transfer Roller clean and free of
toner?

Go to step 5

Clean or
replace the
Bias Transfer
Roller

S4525-17

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды