Xerox DocuPrint N4525 Скачать руководство пользователя страница 248

Страница: 248 / 380

1-226

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-34 Multi-sheet Bypass Feeder Friction
Clutch (PL 4.3)

Removal

Remove the Multi-sheet Bypass Feeder Tray Assembly (RRP 1-26).

Remove the E-ring securing the Clutch to the shaft.

Rotate the Clutch clockwise as you pull it off of the shaft.

Replacement

Make sure the Spacer is in place on the Clutch shaft.

Rotate the Spacer so the tabs on the Spacer mesh with the notches on the
Clutch Gear.

Caution

When performing step 3 below, push only on the rear of the

Clutch. Never press the sides of the Clutch. Pressing the sides of
the Clutch may break the Clutch.

Slide the Friction Clutch onto the shaft, rotating the Clutch as you slide it toward
the Spacer.

Make sure the Clutch and Spacer mesh.

Use the E-ring (removed in Step 2 above) to secure the Clutch to the shaft.

Reinstall the Top Cover.

Reinstall the Multi-sheet Bypass Feeder Tray Assembly (RRP 1-26).

Fig 1-64 Multi-sheet Bypass Feeder Friction Clutch

S4525-107

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды