Xerox DocuPrint N4525 Скачать руководство пользователя страница 195

Страница: 195 / 380

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

173

Press [2] or [6] to
display:

Press [3] or [7] to
display:

Turn -On
Duration

Comment

Tray 2 Lift Mot

2 sec.

1. Press [4] to start test.
2. Actuate Tray 2 Lift Motor for duration or

Press [0] to stop.

Drum Motor On

2 min.

1. Press [4] to start test.
2. Actuate Drum Motor for duration or

Press [0] to stop.

Reg. Clutch On

2 sec.

1. Press [4] to start test.
2. Actuate Registration Clutch for duration or

Press [0] to stop.

Tray 1 Feed Clut

2 sec.

1. Press [4] to start test.
2. Actuate Tray 1 Feed Clutch for duration or

Press [0] to stop.

Tray 2 Feed Clut

2 sec.

1. Press [4] to start test.
2. Actuate Tray 2 Feed Clutch for duration or

Press [0] to stop.

Dev. Bias

2 sec.

1. Press [4] to start test.
2. Turns on Developer Bias output for duration

or Press [0] to stop.

DB AC Clock

2 sec.

1. Press [4] to start test.
2. Turns on DB AC Clock output for duration or

Press [0] to stop.

BCR/AC

2 sec.

1. Press [4] to start test.
2. Turns on Bias Charge Roller AC output for

duration or Press [0] to stop.

BCR/DC

2 sec.

1. Press [4] to start test.
2. Turns on Bias Charge Roller DC output for

duration or Press [0] to stop.

BTR Sel.

2 sec.

1. Press [4] to start test.
2. Turns on Bias Transfer Roller Sel. output for

duration or Press [0] to stop.

BTR RMT

2 sec.

1. Press [4] to start test.
2. Turns on Bias Transfer Roller RMT output

for duration or Press [0] to stop.

DTS

2 sec.

1. Press [4] to start test.
2. Turns on DTS output for duration or Press

[0] to stop.

Fuser Bias

2 sec.

1. Press [4] to start test.
2. Turns on Fuser Bias output for duration or

Press [0] to stop.

Fuser Bias Sel.

2 sec.

1. Press [4] to start test.
2. Turns on Fuser Bias Sel. output for duration

or Press [0] to stop.

Offset Motor Fnt

1 sec.

1. Press [4] to start test.
2. Actuate Offset Motor front

Offset Motor Rev

1 sec.

1. Press [4] to start test.
2. Actuate Offset Motor reverse

CompOutput Test
HCF Unit

Tray 3 Lift

2 sec.

1. Press [4] to start test.
2. Actuate Tray 3 Lift Motor for duration or

Press [0] to stop.

Tray 4 Lift

2 sec.

1. Press [4] to start test.
2. Actuate Tray 4 Lift Motor for duration or

Press [0] to stop.

Tray 5 Lift

2 sec.

1. Press [4] to start test.
2. Actuate Tray 5 Lift Motor for duration or

Press [0] to stop.

Table 1-107 Component Control Output

Press [1] or [5] to display: Main Menu

Comp Output Test

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды