Xerox DocuPrint N4525 Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 175

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

153

Fault History:

The fault history provides two columns of figures to help track faults. A Page Count,

which refers to the actual page count of the printer where a problem occurred. The Fault
Description column lists the Fault (Error) Codes pertaining to the problem. In many

cases, these codes can be found in the Error Codes section of this manual as an aid to
troubleshooting. Not every code is listed in this manual. This fault history can become
helpful in troubleshooting difficult problems by providing the page count/fault description

code to Technical Support, if needed.

1.

While in the menu mode, press [1] or [2] until “PRINT MENU” is displayed.

2.

Press [2] or [6] until “Fault History” is displayed.

3.

Press [4] and the fault history will be printed.

Note

It is advisable to print a fault history and have it ready when
contacting Technical Support.

Menu Map:

The menu map helps the user/technician navigate the multitudes of menus and sub-menus
available. It is a good idea to print a configuration sheet and keep it close to the printer for

reference by users, technicians, and/or system administrators.

1.

While in the menu mode, press [1] or [5] until “PRINT MENU” is displayed.

2.

Press [2] or [6] until “Menu Map” is displayed.

3.

Press [4] and the menu map will be printed.

PS Font List:

The PS Font List produces a list of internally available PostScript fonts. This single test
page is an excellent tool with which to help determine print quality.

1.

While in the menu mode, press [1] or [5] until “PRINT MENU” is displayed.

2.

Press [2] or [6] until “PS Font List” is displayed.

3.

Press [4] and the PS font list will be printed.

PCL

®

Font List:

Three pages of internal PCL fonts is provided with this test. This is another useful print
quality test print.

1.

While in the menu mode, press [1] or [5] until “PRINT MENU” is displayed.

2.

Press [2] until “PCL Font List” is displayed.

3.

Press [4] and the PCL font list will be printed.

PCL

®

Demo Test Print:

The internal PCL Demo test page provides an additional print quality test for the printer.
The page is rich in graphics, black and grayscale painting and text.variations.

1.

While in the menu mode, press [1] until “PRINT MENU” is displayed.

2.

Press [2] until “PCL Demo” is displayed.

3.

Press [4] and the PCL Demo test page will be printed.

«
...
173
174
175
176
177
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды