Xerox DocuPrint N4525 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 179

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

157

Analyzing the Test Print

Test prints provide several uses in troubleshooting printer problems.

Isolating problems to either the print engine or to the System Controller Board

and host software.

Locating feed and paper transport problems.

Detecting print quality and image registration problems.

Using Test Prints to Isolate a Problem to the Print Engine or to the
System Controller Board

You can use test prints to determine if a problem is caused by a faulty print engine or by a
faulty System Controller Board or host software.

Note

This procedure presumes you have investigated any displayed

error code or message. If not, please do so now.

1.

Print a sample image from the host computer.

2.

Enter Printer Diagnostics and generate a test print.

3.

Compare both prints.

4.

If the problem occurs when you print from the host computer but does not occur when
you print from Diagnostics, the problem may be in the System Controller Board, in the

print driver software, or in the application software on the host computer.

5.

If the problem occurs when you print a test print, then the problem is in the print

engine.

Note

You can also use the above procedure to assist in determining if a
print quallty problem is caused by a faulty print engine, system

controller board or host software. If the print quality problem is
an image registration problem, refer to the NVRAM section of this

manual for instructions on adjusting image registration.

Using Test Prints to Locate a Feed or Paper Transport Problem

You can use test prints to locate a problem with paper feed or with paper transportation
along the paper path.

Note

This procedure presumes you have investigated any displayed

error code or message pertaining to paper feed or transport
problems. If not, please do so now.

1.

Enter Printer Diagnostics and generate a test print.

2.

Follow the paper along the paper path to locate the cause of the problem.

«
...
177
178
179
180
181
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды