Xerox DocuPrint N4525 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 185

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

163

Checking Lead Edge Registration

Note

NVM (Non-Volatile Memory) and NVRAM (Non-Volatile Random

Access Memory) are synonymous. NVM is displayed by the
Control Panel. NVRAM appears in documented text.

Note

Use only A4 paper or 8.5” x 11” paper and make certain the tray

being tested is the only tray installed when generating the test
print.

Checking Lead Edge Registration

1.

Generate a Registration Grid Pattern Test Print, see page 1-155 to set up and page

1-156 for specifics on Grid Pattern test print launch.

Note

The Grid Pattern test print on your printer may, or may not,
display edge lines. If no edge lines appear in your test print,

simply measure to the end of any line perpendicular to the Lead
Edge.

2.

Using a metric scale, measure the distance from the lead edge of the test sheet to the
end of any line, or the edge line. The distance should be 4.0 mm (+/- 1.5 mm in

Simplex, +/- 1.9 mm in Duplex), see illustration.

3.

If the line is /- 1.5 mm from the Lead Edge, the printer is within specification.
If it is greater than 1.5 mm, refer to line 16 in Table 1-104 “NVRAM Adjustment

Table,” beginning on page 159 (Lead Edge Registration) for adjustment information.

Note

When checking registration, it is recommended to run test prints

from all available trays and compare individual results before
making any adjustments. Doing this will help you determine

where any adjustments are required.

Adjusting Lead Edge Registration

1.

Enter Diagnostics Mode, see page 1-154.

2.

Press [1] or [5] until “NVM Lead Edge” appears in the bottom line of the display.

3.

Press [2] or [6] until the tray you wish to adjust appears in the bottom line of the

display.

4.

When prompted for a password, sequentially press [0], [7],[3], [4] to gain entry.

5.

Press [3] or [7] once to display the current numerical registration setting.

Fig 1-33 Lead Edge Registration

S4525-72

«
...
183
184
185
186
187
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды