Xerox DocuPrint N4525 Скачать руководство пользователя страница 272

Страница: 272 / 380

1-250

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-62 Exit Roller Assembly (PL 9.2)

Removal

Remove the Exit Drive Assembly (RRP 1-55).

Remove the two black machine screws securing the Face Up Lower Chute to
the Assembly frame, and remove the Chute.

Remove the KL-clip securing the Gear located at the rear of the Exit Roller
shaft, and remove the Gear and rear bearing.

Remove the E-ring securing the front of the Exit Roller shaft to the Assembly
frame, and remove the front bearing.

Slide the shaft to the rear, and remove the shaft from the Assembly.

Fig 1-84 Exit Roller Assembly

Exit Roller

S4525-133

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды