Xerox DocuPrint N4525 Скачать руководство пользователя страница 24

Страница: 24 / 380

1-2

DocuPrint N4525 Network Laser Printer - Service Guide

DocuPrint

N4525 Network Laser Printer Overview

The DocuPrint

N4525 Network Laser Printer is a 45 page per minute

monochrome, 600 dots per inch laser printer that uses a data- modulated laser

beam, standard dry-ink xerographic imaging processes, and heat and pressure

fusing to place a computer generated image onto the surface of a sheet of plain

paper.

The printer uses a semiconductor laser in the Laser Scanner to generate a 5

milliwatt infrared laser beam. Image data sent from the host computer

modulates the beam, creating a latent image on the surface of the electrically

charged xerographic drum.

The printer requires 110VAC @ 60HZ (or, optionally, 220VAC @

50HZ~60HZ) using approximately 900 watts during an average print cycle.

Two power supplies within the printer convert AC line voltage to the various

AC and DC voltages that are needed for printer operation.

Safety circuits within the printer remove power to the printer whenever the

Cover A, Cover B or the Front Cover is opened or the Laser Print (EP)

Cartridge is removed.

The Print Engine Controller Board controls all printer functions, houses printer

diagnostics and supporting test prints, stores operating parameters, and signals

printer errors.

The System Controller board interfaces a host computer with the Print Engine

Controller Board.

The DocuPrint

N4525 Network Laser Printer comes standard with two 500

sheet paper feeders, a 50 sheet Multi-sheet Bypass Feeder, and an offset output

unit. Optional paper feeders are available.

The DocuPrint

N4525 Network Laser has one Customer Replaceable

Consumable (CRC), the Laser Print (EP) Cartridge that must be replaced when

depleted. The printer displays a warning message (“Replace Toner Cartridge”)

when it detects the toner getting low. When the printer detects the toner level is

empty, stops printing until the Laser Print (EP) Cartridge is replaced.

The printer will advise when it is time to install a Maintenance Kit:

At 280,000 page count the printer will display a message informing users of the

impending need to install the Maintenance Kit.

At 300,000 page count the printer will instruct the user to “Install Maintenance

Kit.”

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды