Xerox DocuPrint N4525 Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 263

Volume 1 / Print Engine - FRU RRPs

1

-

241

Removal

1.

Remove the Fuser Assembly.

2.

Remove the Laser Print (EP) Cartridge.

3.

Remove the Offset Exit Unit Assembly (RRP 1-54).

4.

Disconnect J31, J32, and J33 from the AC Driver Board and free the wire
harness from the harness clips.

5.

Disconnect J802 from High Voltage Power Supply-R2 and free the wire
harness from the harness clips.

6.

Remove P204 wire harness from the Fuser Drive Assembly.

7.

Disconnect J104, J456 (on the Input/Output Board), J600, and J602.

8.

Remove the two screws (one black self-tapping and one black machine screw)
securing the Fuser Drive Assembly to the printer frame, and lift the Assembly
off of the frame.

9.

Remove the Input/Output Board and chassis sufficiently to swing out of the way
and access the High Voltage Power Supply (RRP 1-70).

10.

Remove the High Voltage Power Supply sufficiently to access the machine

screw attaching the green wire (ground) termination.

11.

Remove the machine screw securing the green ground wire to the printer

frame.

12.

Pull up and remove the Fuser Drive Assembly.

Replacement

1.

Reinstall the Fuser Drive Assembly onto the printer frame. (Refer to the figure
for correct positioning)

2.

Align the Assembly so the screw holes and locating holes in the Assembly line
up with the screw holes and locating tabs on the frame.

3.

Use two screws to secure the Assembly to the frame.

4.

Reinstall the green ground wire to the printer frame using the machine screw
(removed in Step 11 above) to secure the wire.

5.

Reinstall the High Voltage Power Supply.

6.

Reinstall the Input/Output Board and chassis.

7.

Reconnect J104, J456, J600, and J602.

8.

Reinstall P204 wire harness to the Fuser Drive Assembly.

9.

Reconnect J802 to High Voltage Power Supply-R2 and secure the wire
harness under the harness clips.

10.

Reconnect J31, J32, and J33 to the AC Driver Board and secure the wire

harness under the harness clips.

11.

Reinstall the Offset Unit Assembly (RRP 1-51).

12.

Reinstall the Laser Print (EP) Cartridge (RRP 1-45).

13.

Reinstall the Fuser Assembly (RRP1- 49).

«
...
261
262
263
264
265
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды