Xerox DocuPrint N4525 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 108

1-

86

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-33

Error Code C8-2

Paper Jam

Clear Areas A,B

There is problem with the Tray 2 Take Away Sensor.

Logic Control on the Print Engine Controller Board sensed the Tray 2 Take Away

Sensor was on while the printer was in standby.

Table 1-61 Error Code C8-2 Paper Jam Clear Areas A,B

Step

Actions and Questions

Yes

No

1

Tray 2 TAKE AWAY SENSOR INSPECTION

Inspect the Tray 2 Take Away Sensor for contamination or
paper scraps that may have actuated the sensor.

Is the Sensor clean and free of paper scraps?

Go to step 2

Clean or clear
paper scraps
from the
Sensor

2

Tray 2 TAKE AWAY SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / T/A Roll2 Sensor to test Take-Away Roller 2
Sensor.

3. Press [4] to start, [0] to stop.
4. Open the Left Upper Cover (A).
5. Insert, then remove, a sheet of paper into the Tray 2

Take Away Sensor.

Does the Control Panel display “with paper”
when you insert the paper into the Tray 2 Take
Away Sensor, and is “without paper” displayed
when you remove the paper?

Go to step 3

Replace the
Tray 2 Take
Away Sensor

3

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 4

Problem
solved

4

The following printer components and areas are
associated with this specific problem. One or more of
these components or areas may have failed partially or
completely. If you cannot isolate this problem using the
steps in this Repair Analysis Procedure, replace each
component or troubleshoot each area listed below, one at
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

«
...
106
107
108
109
110
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды