UIC GSM FlexJet Скачать руководство пользователя | Manualshive

Страница: 19 / 114

background image

Page 14

T47541109 Rev. J

FlexJet Head Assembly

TECHNICAL

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

Calibration Table

The following table lists maintenance procedures which require calibrations
after completing the maintenance. Refer to the Calibration, CPE, and
Measurement manual when performing the calibrations required to help
ensure that the component placements are within specifications. (CPE means
Calibration Placement Enhancement.)

Maintenance Procedure

Calibrations Required After Maintenance

Installing a FlexJet Head

• Perform Machine Calibration and Calibration Placement
Enhancement (CPE) for a new head installation.
• Perform CPE for an installation to the previous location of the
head.

Replacing/Aligning a Coupler Body

CPE

Adjusting the Spindle Drive Belt Tension

Spindle Height Calibration and CPE

Setting the Touch-Down Sensors

Spindle Height Calibration

Cleaning the Pin Mirrors

Spindle Height Calibration

Comprehensive Head Maintenance

Spindle Height Calibration, Mirror Calibration, and CPE

Replacing the Stop Brake Belt

CPE

Replacing the Z Stop Brake Assembly

CPE

Replacing a Spindle Touch-Down Sensor

Spindle Height Calibration and CPE

Replacing a Spindle Assembly

Machine Calibration and CPE

Replacing a Clutch

Spindle Height Calibration, Mirror Calibration, and CPE

Replacing a Fiber Optic Cable

Spindle Height Calibration

Replacing a Spindle Drive Belt

Spindle Height Calibration and CPE

«
...
17
18
19
20
21
...
»

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Похожие инструкции для GSM FlexJet

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: CAMAG Страницы: 40

Бренд: J.P. SELECTA Страницы: 32

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды