manualshive.com logo in svg

UIC GSM FlexJet, Руководство пользователя

Поделиться
Скачать
UIC GSM FlexJet Скачать руководство пользователя страница 104

Page 99

FlexJet Head Assembly

T47541109 Rev. J

TECHNICAL

 

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

Disassemble the FlexJet Head

Use ESD precautionary measures when handling the PCA Flex Jet
Control and associated cabling.

1.

Disconnect all cables from the PCA Flex Jet Control.

2.

Remove the PCA Flex Jet Control by removing the 4 side screws and
washers and the 2 upper screws and washers.  Refer to the following
diagram, but leave the upper PC board Bracket mounted to the head.
Do not remove the large Bracket from the PC board.

 OTH Camera Assembly

Head Control Asm PC BD

Bracket

Securing Screws

Platform 
Assembly

3.

Remove the 2 screws and the Optic Bracket from the Optical Sensor
Assy.  But leave the Z Safe emitter and receiver attached.  Refer to the
following diagram.

Optical Sensor Assy

Optic Bracket

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды