manualshive.com logo in svg

UIC GSM FlexJet, Руководство пользователя

Поделиться
Скачать
UIC GSM FlexJet Скачать руководство пользователя страница 89

Page 84

T47541109 Rev. J

FlexJet Head Assembly

TECHNICAL

 

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

7.

Connect the Spindle Touch-Down Sensor Assembly cable to the
appropriate location on the PCA Flex Jet Control.  Refer to the
following diagram and wiring chart.

Spindle Touch-Down
Sensor Assembly 1

Z-Safe
Sensor Assemly 8

PCA Flex Jet Control

From

(Spindle Touch-Down 

Sensor Assy)

To

(PC BD FlexJet Ctrl 

Asm)

P18

18PL

P19

19PL

P20

20PL

P21

21PL

P22

22PL

P23

23PL

P24

24PL

P14

14PL

8.

Install the cable ties securing the Spindle Touch-Down Sensor cable to
the PCA Flex Jet Control.

Final Steps

1.

Set the Touch-Down Sensors so that the light goes off as soon as the
nozzle impacts the component or board.  Refer to Setting the Touch-
Down Sensors procedure located in this document.

2.

Complete the steps in the Prepare the Machine for Production section
of this document to ensure that the machine is in a safe operational
state.  Verify that all covers removed for maintenance are installed,
including the safety covers below the hinged covers and the FlexJet
Head Cover.

3.

Calibrate the spindle height.  Refer to the Calibration, CPE and
Measurement manual.

4.

Perform CPE.  Refer to the Calibration, CPE and Measurement
manual.

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды