manualshive.com logo in svg

UIC GSM FlexJet, Руководство пользователя

Поделиться
Скачать
UIC GSM FlexJet Скачать руководство пользователя страница 90

Page 85

FlexJet Head Assembly

T47541109 Rev. J

TECHNICAL

 

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

Replacing a Clutch

This section describes how to replace a Clutch due to damage or wear.
Replace the appropriate Clutch using the following procedure.

Prerequisites

Ensure that the following items are available before beginning the procedure.

• The Z Belt Tension Tool and the Impact Sensor Setup Tool from the

FlexJet Tool Kit

• Calibration Kit for FlexJet (for Mirror and Spindle Height

Calibrations)

• CPE Kit for FlexJet

• Calibration, CPE and Measurement manual and the Z-Axis Index

Housing Assembly document

Initial Steps

1.

Complete the steps in the Prepare the Machine for Maintenance
section of this document to ensure that the machine is in a safe state for
maintenance.

The machine must be powered down and the site's Lockout/Tagout
procedure executed during this procedure to ensure personal safety.

2.

Remove the FlexJet Head cover.

Be careful when handling the FlexJet Head.  The head is precisely
adjusted and contains delicate parts, especially in the OTH Camera
Assembly.

3.

Remove the FlexJet Head from the machine.  Refer to the Removing a
FlexJet Head procedure located in this document.

4.

Place the FlexJet Head assembly face down in order to access the
clutch assemblies from the rear.  Care must be taken not to damage the
camera or other parts on the front of the head.

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды