manualshive.com logo in svg

UIC GSM FlexJet, Руководство пользователя

Поделиться
Скачать
UIC GSM FlexJet Скачать руководство пользователя страница 51

Page 46

T47541109 Rev. J

FlexJet Head Assembly

TECHNICAL

 

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

Initial Steps

1.

Complete the steps in the Prepare the Machine for Maintenance
section of this document to ensure that the machine is in a safe state for
maintenance.

The machine must be powered down and the site's Lockout/Tagout
procedure executed during this procedure to ensure personal safety.

2.

Complete the steps in the Removing a FlexJet Head section of this
module before performing the Comprehensive Head Maintenance
procedures.  Use an ESD-dissipative foam pad for cushioning between
the head and the work surface if one is available.

Clean the Pin Mirrors

Use the following procedure to clean both Pin Mirrors on each FlexJet
Spindle.  If the Pin Mirrors are covered with dust, oil, or other contamination,
the performance of the FlexJet Head touch-down sensors may decrease.

1.

Remove the Plate and Baffle from the head casting.  Refer to the
following diagram.

Captive

Screws

2.6 OTH Camera Asm

Camera Cable Assy

Baffle

Plate

Be careful when handling the 7 CCD Camera Assembly.  It is a delicate
device.

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды