UIC GSM FlexJet Скачать руководство пользователя | Manualshive

Страница: 57 / 114

background image

Page 52

T47541109 Rev. J

FlexJet Head Assembly

TECHNICAL

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

2.

Inspect the clear hoses connected to the Manifold Assembly for proper
seating. If a hose is loose, but appears in good condition, firmly
connect the hose to the fitting. If a hose is damaged, it must be
replaced.

3.

Inspect the Coupler Body hoses for proper seating. See the diagram to
the left. If a hose is not seated correctly, push the hose onto the fitting
until it is completely seated.

Coupler Body Hoses

Nozzle Tip

Clean the Camera Mirrors

Use the following procedure to clean contamination from the 2.6 OTH
Camera mirrors.

Never wipe mirrors with anything that is dry because they are
susceptible to scratching. Use only a lens solution and tissue designed
for delicate optical surfaces to clean the camera mirrors. The mirror
surfaces can be damaged by solutions and tissue not formulated for
optical surfaces or lenses. Also be aware that fingerprints on the
camera mirrors may reduce the performance of the head.

If the movable mirror is damaged, the entire Slide Mirror assembly must
be replaced. In addition, if the stationary image-path mirror is damaged,
it must be replaced. However, the side-plate mirror surfaces are for
illumination only and the impact of a small scratch is negligible.

1.

While holding the movable mirror in the up position, apply any
commercially available quality optics/lens cleaning solution to lens
tissue and clean the stationary mirror and 2 side mirrors. Then wipe
the surface clean with the lens tissue.

Do not continue to wipe the mirror surfaces after the solution is
removed. If a stain or particle is still present after the first attempt, then
apply more solution and repeat. However, never wipe the mirrors with
a dry tissue. Also, do not wipe the mirrors with a soiled portion of a
tissue.

Be careful not to let go of the movable mirror when it is in the upper
position, or the springs will abruptly pull the mirror to its rest position.

2.

Carefully clean the movable mirror in the same manner as the other
mirrors and return the movable mirror to its rest position.

3.

Inspect the 2 image mirrors for significant scratches. If significant
scratches are visible, contact a Universal Technical Specialist.

«
...
55
56
57
58
59
...
»

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Похожие инструкции для GSM FlexJet

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: UFO Страницы: 16

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: Obdstar Страницы: 42

Бренд: Ognibene Страницы: 28

Бренд: Hameg Страницы: 24

Бренд: Vaisala Страницы: 118

Бренд: Ibiza Страницы: 21

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды