UIC GSM FlexJet Скачать руководство пользователя | Manualshive

Страница: 17 / 114

background image

Page 12

T47541109 Rev. J

FlexJet Head Assembly

TECHNICAL

PUBLICATIONS

This Document Supports Assembly 47541109 Rev. F

Functional Description

The FlexJet® Head Assembly is a high-speed, 7-spindle flexible-placement
head. This head can gang pick components up to 12 mm square, inspect
components on the fly using an On-The-Head (OTH) Camera, and place
components in sequential order. All Z axis motion is controlled by one drive
mechanism.

Maintenance Concept

The following Maintenance Concept tables summarize maintenance and
operational procedures for this assembly. For a more detailed explanation of
the Maintenance Concept and its structure refer to the Prerequisite
Information and Introduction module in the platform Maintenance Support
Document.

Ensure that the FlexJet or Platform Tool Kits are available if they are
required for a procedure. These kits contain measurement and setup tools.

Adjustments and Other Procedures for
Maintenance Technicians

The following procedures require a minimum skill level of Maintenance
Technician and should be performed only as required to ensure proper
functioning of the FlexJet Head.

Maintenance Procedures

Recommended

Frequency

Minimum Skill

Required

Spares Kit

Required

Universal Tool Kit

Required

Installing a FlexJet Head *

As Required

Maintenance

Technician

No

No

Removing a FlexJet Head

As Required

Maintenance

Technician

No

No

Head/Changer Nozzle Setup

As Required

Maintenance

Technician

No

No

Replacing/Aligning a Coupler Body *

As Required

Maintenance

Technician

No

FlexJet Tool Kit

Zeroing the Theta Encoder

As Required

Maintenance

Technician

No

FlexJet Tool Kit

Adjusting the Z-Safe Sensor

As Required

Maintenance

Technician

No

No

Adjusting the Spindle Drive Belt Tension *

As Required

Maintenance

Technician

No

FlexJet Tool Kit

Setting the Touch-Down Sensors *

As Required

Maintenance

Technician

No

FlexJet Tool Kit

Adjusting the Stop Brake Belt Tension

As Required

Maintenance

Technician

No

No

Replacing the FlexJet PCA Control

As Required

Maintenance

Technician

No

No

* Calibration is required. Refer to the Calibration Table section.

«
...
15
16
17
18
19
...
»

Содержание GSM FlexJet



















































































































Отзывы:

Нет отзывов

Похожие инструкции для GSM FlexJet

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: JBM Страницы: 12

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Nabtesco Страницы: 26

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Qlight Страницы: 4

Бренд: Rath Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды