manualshive.com logo in svg

Tektronix 492, 492P, Руководство по обслуживанию


Поделиться
Скачать
background image

Theory of Operation—492/492P Service Vol.  1  (SN B030000 &  up)

The FINE TUNE VOLTS signal from the Center Frequen­

cy Control circuits, which is used to tune the 2nd Local Os­
cillator,  is  applied  to the input of  U2047.  Since it is  applied 
here,  this  makes  the  fine  tune  voltage  independent  of  the 
voltage tripling action in the voltage processor section. The 
tuning  voltage  is  also  applied  to  the  input  networks  of 
U2045.  Thus,  by  varying  the magnitude of signal in  the  in­
verting path compared to the direct path, the proper magni­

tude  and  polarity  of  fine  tune  offset  for  each  IF  offset  is 
provided in the preselector drive signal. Table 5-16 lists the 
offset voltage required for each frequency band.

Summing  Amplifier

The  effective  oscillator  frequency  voltage  from  U2028 

and  the  offset  IF  voltage  from  U2045  are  applied  to  the 
inverting input of U2047. This stage drives the tracking ad­

justments  stage  and  furnishes  a  signal  for  external 

preselector drive circuits as well. The external drive line has 
its own return to reduce ground loops.

Tracking  Adjustments

These circuits consist of gain-setting offset  and shaping 

circuits.  R1065  (PRE-SEL  SENSE)  is  used  to  compensate 
for sensitivity variations between preselector stages. R1064 
(PRE-SEL OFFSET)  is  used  to  compensate  for  the  offset 
introduced  in  previous  circuits  and  for  any  offset  in  the 
preselector. This adjustment sets the preselector frequency 
to 2072 MHz when the output of U2047 is at zero volts.

The four other adjustments (R1054,  R1056,  R1061,  and 

R1063), are part of a shaper network. The network compen­

sates  for  magnetic  saturation  in  the  preselector,  which 
would cause a deviation from linearity at frequencies above 
14 GHz.  Each  shaper network is  switched  in  by a  resistive 

divider that,  at a given frequency, forward-biases the diode 

in the shaper to shape the current output. Thus, the diodes 

compensate for the non-linear action of the YIG tuning.

The front  panel  PEAKING  control applies  a  small  offset 

through R5065 to the input of the current driver stage. This

corrects for non-linearity or temperature drift  in  the  1 st  LO 
or Preselector.

Current Driver

This stage consists of output stage Q5065/Q5052;  FETs 

Q3061,  Q3077,  and  Q2074;  amplifiers  U2054  and  U3054; 
and transistor Q4037.

FET  Q2074,  as  controlled  by  the  Q3  line  of  U5031,  is 

turned  off  to  reduce  the  coil  current  to  zero  when  the 
preselector is not in  use, or during a degauss cycle.  During 
normal operation, the transistor is conducting.

Preamplifier  U2054  reduces the  temperature drift of the 

output  stage.  Driver offset  adjustment  R2066  nulls  the off­

set  voltage,  at  which  point  the  temperature  drift  is  least. 
U2054  drives  U3054,  the  main  operational  amplifier.  FET 

Q3061  isolates  U3054 from the output driver.

Current amplifier Q5052 drives the main preselector driv­

er  transistor,  Q5065.  The  stage  is  biased  so  current  flow 
divides  with  most  of the  current  going  through  the  output 
transistor,  and  a  small  portion  flows  through  the  bias  cir­
cuits.  The  currents  rejoin  at  the  preselector  coil.  Resistor 
R4049  has  four terminals;  one set carries  the  coil  current, 

the other set senses the voltage and thus the coil current.

When the  preselector is not being swept,  line 06 is low, 

which causes Q4037 to conduct. This causes Q3077 to con­
duct, placing C4071  across the Preselector coil. The capaci­
tor reduces noise at the output.

Preselector Switch  Driver

Operational  amplifier  U1011B  and  the  complementary 

pair  of  transistors  Q4025/Q3025,  form  the  preselector 
switch  driver.  This  circuit  drives  the  latching  relay  that  is 

depicted on Diagram 12. This relay requires a positive pulse 
to select the low-pass filter,  and  a negative pulse to  select 
the preselector.

Table  5-16 

PRESELECTOR  FREQUENCY  BANDS

Band

Frequency Range

IF

Harmonic

A pproxim ate 

Voltage  O ffset

2

1.7—5.5 GHz

-82 9  MHz

1

st

9.0 volts

3

3.0—7.1  GHz

+ 829 MHz

1

st

3.9 volts

4

5.4—18.0 GHz

-82 9  MHz

3rd

9.0 volts

5

15.0—21.0 GHz

+ 2.072 GHz

3rd

0

 volt

REV AUG  1981

5-65

Содержание 492, 492P
















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 492, 492P

Olympus EPOCH 650 User Manual preview
EPOCH 650
Бренд: Olympus Страницы: 362
Olympus 27MG Getting Started Manual preview
27MG
Бренд: Olympus Страницы: 8
Yamaha Disklavier E3 Quick Reference Manual preview
Disklavier E3
Бренд: Yamaha Страницы: 10
Yamaha Disklavier E3 Playing Manual preview
Disklavier E3
Бренд: Yamaha Страницы: 38
Yamaha Disklavier E3 Update Manual preview
Disklavier E3
Бренд: Yamaha Страницы: 45
Halma SENSITRON SMART S Short Installation Manual preview
SENSITRON SMART S
Бренд: Halma Страницы: 12
Quarton ML-400 Instructions preview
ML-400
Бренд: Quarton Страницы: 2
Horiba Scientific LAQUA F-74BW Quick Manual preview
LAQUA F-74BW
Бренд: Horiba Scientific Страницы: 2
SensorLink 6-120 Operator'S Manual preview
6-120
Бренд: SensorLink Страницы: 12
DAPAudio IEM-100 Beltpack Product Manual preview
IEM-100 Beltpack
Бренд: DAPAudio Страницы: 17
MADDALENA microCLIMA ULTRA Installation And Operating Instructions Manual preview
microCLIMA ULTRA
Бренд: MADDALENA Страницы: 17
Halo Photonics Stream Line Pro Hardware And Software Manual preview
Stream Line Pro
Бренд: Halo Photonics Страницы: 45
Dive Perfect Stubby LED-1500 User Manual preview
Stubby LED-1500
Бренд: Dive Perfect Страницы: 4
pts Diagnostics A1CNow Quick Reference Manual preview
A1CNow
Бренд: pts Diagnostics Страницы: 2
Spectroline LeakTracker OIL-GLO ULTRA Instruction Manual preview
LeakTracker OIL-GLO ULTRA
Бренд: Spectroline Страницы: 12
Hach DR/2000 Instruction Sheet preview
DR/2000
Бренд: Hach Страницы: 4
Parkside PZM 2 A1 Operation And Safety Notes preview
PZM 2 A1
Бренд: Parkside Страницы: 199
EUTECH INSTRUMENTS WATERPROOF PHTESTR 1 PH TESTER Instruction Sheet preview
WATERPROOF PHTESTR 1 PH TESTER
Бренд: EUTECH INSTRUMENTS Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды