Sony DVW-250 Скачать руководство пользователя страница 80

Страница: 80 / 272

6-10

DVW-250/250P

6-2. Brush Replacement

2. Brush assembly removal

(1) Disconnect the connector CN913 on the MB-

601 board.

(2) Remove one of the screws, shown in the

figure, which secures the brush base.

(3) Loosen the other screw and move the brush

base in the direction of the arrow.

In this way, the brush and slip ring will

release.

(4) Remove the screw and the brush assembly.

(5) Disconnect the connector on the brush board.

Installation

3. Brush assembly installation

(1) Connect the connector to the brush board.

(2) Temporarily attach the brush assembly to the

brush support with the screw shown in the

figure.

Never touch the brush.

(3) Move the brush base (arrow A) while press-

ing down the brush base above the brush

support and temporarily attach the brush

assembly using the other screw.

(4) While pushing the brush base (arrow B),

tighten the screws in steps (2) and (3).

Slip ring

Brush

Brush base

Remove this screw first.

(P2

Slip ring

Brush

Brush base

Temporarily fasten
this screw first.

Brush support

Screw(P2

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды