Sony DVW-250 Скачать руководство пользователя страница 65

Страница: 65 / 272

5-3

DVW-250/250P

5-1-3. Cleaning of Tape Running Surface of Lower Drum and Lead Surface

Notes

Take care not to damage the lower drum (specially lead surface) during cleaning. Take care to clean the edge portion above

the lower drum because it is near the video heads.

Tools

• Cleaning cloth : 3-184-527-01

• Cleaning fluid : 9-919-573-01

• Skewer or an equivalent (A metallic skewer can not use.)

Procedures

Put a skewer (or an equivalent) along the drum lead surface and remove magnetic powder as shown in the figure.

(a) Do not use a metallic skewer instead of a skewer. This may damage the tape running surface.

(b) If the magnetic powder attached to the drum lead surface, tracking may badly influence.

Remove the magnetic powder completely.

Clean the tape running surface of the lower drum and lead surface (shaded portion) using a cleaning cloth moistened

with cleaning fluid as shown in the figure.

After cleaning, be sure to wipe the tape running surface of the lower drum and lead surface using a dry cleaning cloth.

5-1. Cleaning

Skewer(Bamboo)

Lead surface

Tape running surface
of the lower drum

Cleaning cloth

Lead surface

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды