Sony DVW-250 Скачать руководство пользователя страница 17

Страница: 17 / 272

1-7

DVW-250/250P

Threading FG sensor

The threading FG sensor detects the rotation speed of the threading motor.

The FG output signal of this detection sensor is input to the servo circuit to control the threading

speed so that the tape is not damaged during threading and unthreading.

Tape top sensor

This sensor detect the top of the tape, and in addition detects the tape end of the tape that runs in the

reverse direction.

Threading-end sensor

Unthreading-end sensor

These sensors detects whether S/T drawer guides and S/T sliders reach the threading-end or un-

threading-end position by rotation angle of the gear.

L casette sensor

This sensor detects whether the inserted cassette tape is an L size.

L cassette REC inhibit sensor

This is a REC inhibit plug detector switch for the digital large cassette.

Cleaning tape detect sensor

Using a tub on the back side of the cassette tape, this sensor detects whether a cleaning tape is being

inserted into the unit.

Tape thickness sensor

Using a tub on the back side of the cassette tape, this sensor detects the thickness of the tape wound

on a cassette tape that is being inserted into the unit.

Metal/oxide tape sensor

Using a tub on the back side of the cassette tape, this sensor detects whether an oxide tape or metal

tape is being inserted into the unit. (Only during analog tape playback)

10: Analog/digital tape sensor

Using a tub on the back side of the cassette tape, this sensor detects whether an analog tape or digital

tape is being inserted into the unit.

11: Reel hub diameter sensor

The reel hub diameter of a cassette tape varies depending on the length of the tape wound on the

cassette tape. The reel hub diameter sensor detects the reel hub diameter using a tub on the back side

of the cassette tape. The output signal of this sensor is input to the servo circuit to control the

rotation speed and torque of the reel motor.

12: Condensation sensor

This sensor detects whether the dew condensation occurs in the unit.

13: S cassette REC inhibit sensor

This is a REC inhibit plug detection switch for the digital small cassette.

14: Tape end sensor

This sensor detects the end of the tape that runs in the forward direction.

15: S tension regulator arm sensor

During recording and playback, this sensor detects the tension arm position and controls the reel

torque to keep a constant S tape tension.

1-2. Locations of Main Part and Functions of Printed Circuit Board

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды