Sony DVW-250 Скачать руководство пользователя страница 196

Страница: 196 / 272

7-22

DVW-250/250P

2. T1 guide slantness adjustment

(1) Turn the tracking control volume using a screwdriver

so that the output level at the center of the envelope

waveform is the maximum.

(2) Turn the upper flange of the T2 guide counterclock-

wise, and adjust the height so that the tape runs

without contacting the upper and lower flanges of the

T2 guide.

(3) Adjust the slantness of the T1 guide so that the

envelope waveform meets the specification.

Perform the T1 guide slantness adjustment as follows.

(4) Eject the alignment tape and insert it and play back

again.

(5) Check that the envelope waveform A meets the

specification.

If not, perform the steps (3) and later.

(6) Tighten the set screws

and

Tightening torque:

0.1

0.015 N • m (0.8

0.15 kgf•cm)

3. T1 guide slantness check

Repeat the mode change from EJECT mode to PLAY

mode 3 times. Check that the envelope waveform A meets

the specification.

If not, perform step 1) and later again.

Enverope waveform

A = 2.5 ±1.5 ms

Spec :

T1 guide

Screw

• To lengthen the A
(1) At first , loosen the screw

(2) And then, tighten the screw

• To shorten the A
(1) At first , loosen the screw

(2) And then, tighten the screw

7-2-8. T1 Guide Slantness Adjustment

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды