Sony DVW-250 Скачать руководство пользователя страница 83

Страница: 83 / 272

6-13

DVW-250/250P

6-3. Slip Ring Assembly Replacement

3. Slip ring assembly removal

(1) Unsolder the three leads of the slip ring

assembly from the UDR-9 board on the upper

drum assembly.

(2) Remove the two screws and the slip ring

assembly.

Installation

4. Slip ring assembly installation

(1) Attach the slip ring assembly to the drum

shaft so that the three leads of the slip ring

assembly are positioned to the printed silk

(RED, BLUE, and BLK) on the UDR-9 board

of the upper drum assembly.

Hold the black portion of the slip ring

assembly during installation. Never touch the

slip ring.

(2) Attach the slip ring assembly using the two

screws.

Tightening torque: 19

–2

N•m (1.9 kgf•cm)

(3) Solder the three leads of the slip ring assem-

bly to the UDR-9 board of the upper drum

assembly.

Red lead : RED pattern

Blue lead : BLUE pattern

Black lead: BLK pattern

5. Brush assembly installation

Install the brush assembly. (Refer to “6-2. Brush

Replacement”.)

6. Brush cover installation

Install the brush cover. (Refer to “6-2. Brush

Replacement”.)

UDR-9 board

Leads

Slip ring

RED

BLK

BLUE

Screws(P2

UDR-9 board

Leads

Upper drum assembly

Slip ring

Soldered points

Screw(P2

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды