Sony DVW-250 Скачать руководство пользователя страница 109

Страница: 109 / 272

6-39

DVW-250/250P

6-11. Tension Regulator Roller Replacement

2. Tape guide height check

(1) Insert the cassette tape into the cassette

compartment.

(2) Put the manual eject gear downward and turn

it clockwise while pulling the brake release

lever until the S slider reaches around the FE

head.

(3) While putting the manual eject gear down-

ward and pulling the brake release lever, turn

the manual eject gear counterclockwise about

180 degrees so that the threaded tape is

stretched taut.

The tape is then pulled out from the cassette

tape and threaded to the tension regulator

roller.

(4) Check that the tape is threaded without

curling on the upper and lower flanges of the

tension regulator roller. If the tape curls,

adjust according to the following procedures.

(a) Loosen the setscrew of the upper flange.

(b) Turn the upper flange and eliminate the

tape curl.

(5) Push the manual eject gear downward and

turn it counterclockwise while pulling the T

reel brake release lever.

The unit is then put into the unthreading

mode, and the drawn tape is rewound to the

cassette.

Tape

Tension regurator

S drawing arm

Lower frange

Upper frange

Curl

S slighder

Erase head

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды