manualshive.com logo in svg

Sony DVW-250, Руководство по обслуживанию

Поделиться
Скачать
Sony DVW-250 Скачать руководство пользователя страница 9

DVW-250/250P

7

Purpose of this manual

This manual is the maintenance manual of Digital Videocassette Recorder DVW-

250/250P.

This manual describes the maintenance information of this unit, and the information

on primary services such as the replacement of main blocks and circuit boards.

Contents

The following is a summary of the sections for understanding the contents of this

manual.

Section 1

Service Overview

Explains the locations of main part, the functions of printed circuit board, the

removal and installation of cabinet, and the measures against trouble.

Section 2

Error Message

Explains the error messages.

Section 3

Maintenance Mode

Explains the maintenance mode of this unit.

Section 4

Overall Block Diagrams and Circuit Descriptions

Describes the overall block diagrams and the circuit descriptions.

Section 5

Periodic Maintenance and Inspection

Explains the cleaning procedures and periodic checks.

Section 6

Replacement of Mechanical Parts

Explains how to replace the parts that should replace periodically and how to adjust

them after the replacement.

Section 7

Tape Path Alignment

Explains the adjustment procedures of tape path system.

Section 8

Replacement of Circuit Boards

Explains how to replace the main boards.

Section 9

Electrical Alignment

Explains the general information for electrical adjustments and the electrical adjust-

ments of this unit.

Section 10 Spare Parts

Describes the exploded views for the unit and mounted/printed circuit boards list.

Manual Structure

Содержание DVW-250

















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды