Sony DVW-250 Скачать руководство пользователя страница 86

Страница: 86 / 272

6-16

DVW-250/250P

6-4. Upper Drum Assembly Replacement

3. Unsoldering the leads of slip ring

assembly

Unsolder the three leads of the slip ring assembly

from the UDR-9 board on the upper drum

assembly.

4. Upper drum assembly removal

(1) Put an L wrench into the holes of the upper

drum assembly and remove the four screws.

(2) Lift just above and remove the upper drum

assembly.

• Be careful not to damage the upper edge of

the lower drum after the upper drum

assembly is removed.

• Remove the screws from the removed

upper drum assembly using a pair of

tweezers.

Upper drum

Screw holes

Upper drum

UDR-9 board

Leads(red, blue, black)

Soldering

Slip ring

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды