Sony DVW-250 Скачать руководство пользователя страница 106

Страница: 106 / 272

6-36

DVW-250/250P

6-10. Pinch Solenoid Assembly Replacement

Installation

2. Pinch solenoid assembly installation

(1) Attach the pinch solenoid assembly to the

chassis while putting the parallel pin of an

iron core into the groove of the pinch lever,

and fix the pinch solenoid assembly with the

two screws.

(2) Connect the harness connector of the pinch

solenoid to connector CN953 and the connec-

tor of the reel motor to connector CN951 on

the MB-601 board.

(3) Fasten the harness by the harness clamper.

Adjustment after replacement

3. Pinch solenoid assembly position

adjustment

(1) Put the unit into the threading end mode by

turning the manual eject gear.

(2) Check that the clearance shown in the figure

meets the specification when the upper

portion of the parallel pin is pushed using a

(–)2 mm flatblade screwdriver so that the iron

core of the pinch solenoid is put into the

energized state.

If not, perform the following steps.

(3) Loosen the two screws fixing the pinch

solenoid assembly to the chassis, move the

pinch solenoid assembly in the direction of

the arrow, and tighten the screws.

(4) Perform step (2) again and check that the

specification is met.

4. Tape path adjustment

(Refer to Section 7-1-1.)

Solenoid base

Parallel pin

Screws

Solenoid

Harness

Harness clamper

Screws

Parallel pin
(Push using screwdriver)

Spec. : A = 0.3 ±0.1 mm

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды