Sony DVW-250 Скачать руководство пользователя страница 223

Страница: 223 / 272

7-49

DVW-250/250P

7-2-19. Tape Running Check

10. Tape running check around the capstan shaft

(1) Put into the REW mode any portion of BCT-D124L.

After 2 or 3 seconds, put into the play back mode.

When changing the mode, check that the tape running

condition meets specification 3 between CUE head

and capstan shaft.

Specification 3

Tape runs without any wrinkle.

If the tape wrinkle occurs, check that the tape wrinkle

disappears within 2 seconds and do not damage the tape.

(2) Repeat the step (1) 2 or 3 times and re-check.

(3) Put into the F FWD mode, and after 2 or 3 seconds put

into the PLAY mode.

Check that the specification is met.

If not, Perform the steps 10) and later.

(4) Put into the REV SEARCH mode, and after 2 or 3

seconds put into the PLAY mode.

Check that the specification is met.

If not, perform the adjustment from “7-2-11. T3 Guide

Height Adjustment”.)

T3(T-drawing)
tape guide

Capstan

CUE/TC head

Pinch roller

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды