Sony DVW-250 Скачать руководство пользователя страница 199

Страница: 199 / 272

7-25

DVW-250/250P

7-2-10. Alignment Tape Tracking Check

Tools

• Alignment tape ZR2-1

8-960-073-11

• Alignment tape ZR2-1P

8-960-073-61

• Oscilloscope

• Regulated DC power supply (AC-550/550CE or equiva-

lent)

Setting

Turn the power off.

Remove the top panel.

(Refer to “1-5. Removal/Installation of Cabinet”.)

Open the ornamental panel on the left side panel.

(Refer to “1-13. Tracking Adjustment”.)

Connect an oscilloscope.

CH-1: TP10/MB-601 (REC A)

TRIG: TP8/MB-601 (CF)

Connect a regulated DC power supply to DC IN

connector on the connector panel.

Turn the power on.

On the setup menu, set AUTO TRACKING to OFF.

Insert an alignment tape ZR2-1/1P.

Checks

1. Playback the alignment tape.

Play back the alignment tape ZR2-1/1P (from 00:00 to

15:00).

7-2-10. Alignment Tape Tracking Check

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды