Sony DVW-250 Скачать руководство пользователя страница 72

Страница: 72 / 272

6-2

DVW-250/250P

6-1. General Information for Mechanical Part Replacement

6-1-2. Threading End/ Unthreading End Mode

1. Threading end mode

Threading end mode means that the S and T sliders move from around the reel tables

to both sides of the drum, and stop at the cut portions like a V of the catchers S and T.

And the S drawing arm and T dawing arm are fixed at the portion that shown in

folloing figure.

(1) To enter the threading end mode with a tape

• Insert a cassette tape into the cassette compartment.

• Close the front lid.

(2) To enter the threading end mode without a tape

When no cassette is in the cassette compartment, do not turn the red gear on

the left of the cassette compartment.

• Turn the power off.

• Remove the top panel.

• During pushing the T reel brake release lever, turn the manual eject gear

clockwise as far as it will go while pushing it downward.

Cacher S

Cacher T

S drawing arm

T drawing arm

Manual eject gear
(red)

Red gear

Cassette
compartment

T reel brake release
lever (red label)

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Похожие инструкции для DVW-250

Бренды по названию

Популярные бренды