Sony DVW-250 Скачать руководство пользователя страница 24

Страница: 24 / 272

1-14

DVW-250/250P

1-6. Cassette Compartment Removal/

Installation

Be sure to turn the power off, and remove the power cord

and/or battery.

Removal

Put the unit into the intermediate position of the reel

tables. (Refer to Section 6-1-5.)

Remove the four screws on the side of the unit.

Disconnect the connector CN957 from the MB-601

board.

Remove the cassette compartment from the unit.

Notes During Installation

• When install the cassette compartment, be careful not to

put the harness between the connector panel and front

panel.

• Attach the cassette compartment in the chassis so that

the two guide pins of the cassette compartment are put

into the round holes of stage.

1-7. Connector Panel Removal/

Installation

Removal

Remove the top plate, handle, bottom plate, battery

case and cassette compartment. (Refer to “1-5. Re-

moval/Installation of Cabinet” and “1-6. Cassette

Compartment Removal/Installation”.)

Disconnect the connectors CN551, CN552 and CN553

on the ADA-44 board. And then remove the clamper.

Open the video boards assembly. (Refer to Section 8-

2-1.)

Disconnect the connectors CN101, CN105, CN106,

CN108 through CN110, CN112 and CN113 on the

SST-3 board.

Disconnect the connectors CN921, CN923 and CN930

on the MB-601 board. And then disconnect the

connectors CN601 and CN912 on the DC/DC convert-

er.

Remove the four screws and remove the connector

panel from the unit.

Note During Installation

After install the connector panel, perform the tape path

adjustment. (Refer to Section 7-2.)

1-6. Cassette Compartment Removal/Installation
1-7. Connector Panel Removal/Installation

Screw(B3

Connector panel

Screw(B3

Screw
(B3

CN957

Cassette compartment

Screws
(B3

Screws(B3

MB-601 board

Содержание DVW-250

















































































































































































































































































Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды

Sony DVW-250, Руководство по обслуживанию

Результаты поиска

Содержание DVW-250

Отзывы:

Бренды по названию

Популярные бренды