manualshive.com logo in svg

Renesas RL78/G1P, Руководство пользователя по оборудованию, Страница: 257 / 770

Поделиться
Скачать
Renesas RL78/G1P Скачать руководство пользователя страница 257

 

RL78/G1P 

 

CHAPTER  8   WATCHDOG  TIMER 

R01UH0895EJ0100  Rev.1.00 

 

 

238  

Nov 29, 2019 

8.4.3  Setting window open period of watchdog timer  

Set the window open period of the watchdog timer by using bits 6 and 5 (WINDOW1, WINDOW0) of the option byte 

(000C0H).  The outline of the window is as follows. 

 

  If “ACH” is written to the watchdog timer enable register (WDTE) during the window open period, the watchdog timer 

is cleared and starts counting again. 

 Even if “ACH” is written to the WDTE register during the window close period, an abnormality is detected and an 

internal reset signal is generated. 

 

Example

: If the window open period is 50% 

 

Window close period (50%)

Window open period (50%)

Counting

starts

Overflow

time

Counting starts again when
"ACH" is written to WDTE.

Internal reset signal is generated
if "ACH" is written to WDTE.

 

 

Caution  When data is written to the WDTE register for the first time after reset release, the watchdog timer is 

cleared in any timing regardless of the window open time, as long as the register is written before the 

overflow time, and the watchdog timer starts counting again. 

 

Содержание RL78/G1P



































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов