Nidec LEROY-SOMER Powerdrive FX, Руководство по вводу в эксплуатацию

Страница: 93 / 176

93
ADVANCED PARAMETER-SETTING MODE
Commissioning manual Powerdrive MD2/FX
4617 en - 2017.09 / e
08.21 : DI1 input destination
Adjustment range : 00.00 to 21.51
Factory setting : 00.00
Format: 16 bits
This parameter is used to select the destination of digital input 1.
Any non-protected «bit» type parameter can be assigned to
the input.
If an unsuitable parameter is addressed, no assignment is
taken into account.
CAUTION:
If 05.70 is set to «Drive terminal (1)» or «2 PTC inputs (3)»,
then digital input DI1 must not be used (do not assign
08.21 ).
08.22 : DI2 input destination
Adjustment range : 00.00 to 21.51
Factory setting : 01.45 : Reference selection
Format: 16 bits
This parameter is used to select the destination of digital input 2.
Any non-protected «bit» type parameter can be assigned.
If an unsuitable parameter is addressed to the input or output,
no assignment is taken into account.
08.23 : DI3 input destination
Adjustment range : 00.00 to 21.51
Factory setting : 01.41 : Reference selection
Format: 16 bits
This parameter is used to select the destination of digital input 3.
Any non-protected «bit» type parameter can be assigned.
If an unsuitable parameter is addressed to the input or output,
no assignment is taken into account.
08.24 : DI4 input destination
Adjustment range : 00.00 to 21.51
Factory setting : 06.30 : FWD/Stop
Format: 16 bits
This parameter is used to select the destination of digital input 4.
Any non-protected «bit» type parameter can be assigned to
the input.
If an unsuitable parameter is addressed, no assignment is
taken into account.
08.25 : DI5 input destination
Adjustment range : 00.00 to 21.51
Factory setting : 06.32 : Rev/Stop
Format: 16 bits
This parameter is used to select the destination of digital input 5.
Any non-protected «bit» type parameter can be assigned to
the input.
If an unsuitable parameter is addressed, no assignment is
taken into account.
08.26 : DO1 Digital Output source
Adjustment range : 00.00 to 21.51
Factory setting : 10.03 : Zero speed
Format: 16 bits
This parameter is used to select the source which you wish to
assign to digital output DO1.
Any non-protected «bit» type parameter can be assigned.
If an unsuitable parameter is addressed, no assignment is
taken into account.
08.27 : Output relay 1 source
Adjustment range : 00.00 to 21.51
Factory setting : 10.01 : Drive healthy
Format: 16 bits
This parameter is used to select the source for the output relay.
Any non-protected «bit» type parameter can be assigned.
If an unsuitable parameter is addressed, no assignment is
taken into account.
08.28 : Output relay 2 source
Adjustment range : 00.00 to 21.51
Factory setting : 10.52 : V
max
alarm
Format: 16 bits
This parameter is used to select the source for the output relay.
Any non-protected «bit» type parameter can be assigned.
If an unsuitable parameter is addressed, no assignment is
taken into account.
08.29 : Digital input polarity
Adjustment range : Negative (0) or Positive (1)
Factory setting : Positive (1)
Format: 8 bits
This parameter is used to change the polarity of digital inputs.
Negative (0):
Negative logic.
Positive (1):
Positive logic.
08.30 to 08.49 : Not used
08.50 to 08.53 : Buffers 1 to 4
Adjustment range : Inactive (0) or Active (1)
Factory setting : Inactive (0)
Format: 8 bits
Binary parameters that can be used as buffer variables.
CAUTION:
At each power-up, parameters 08.50 to 08.53 revert to (0).
08.54 to 08.97 : Not used