NF EC1000SA Скачать руководство пользователя

Страница: 90 / 283

4.4

Using the Sequence Function

EC1000SA

4-22

4.4 Using the Sequence Function

4.4.1 Sequence operations

When the sequence function of the EC1000SA is used, the pattern to be output can be freely programmed.

For example, if a series of voltage change patterns that will be used in voltage variation tests for car

electronics are programmed in advance, the output will change according to the sequence, so the test can

be completed in one series of operations.

In the sequence operation programming, DC, sine waves, and square waves, which are built in the

EC1000SA, and arbitrary waveform (16 types) captured via the USB interface is able to use. Maximum

step number is 255 (minimum step time is 0.1 ms). In each step, waveform, level, and duration time can be

set and constant/keep/sweep can be chosen. In addition, sequences can be repeated from 1 to 999 times (or

continuously). The EC1000SA is also equipped with other functions, such as for branching to a specified

step during a sequence operation, and for starting, stopping, or holding a sequence operation.

Data is saved to sequence memory automatically.

These sequence functions can be used in AC-INT mode or AC+DC-INT mode.

Number of sequences: Retained for each operation mode (AC/AC+DC) and each output voltage

range (100 V/200 V).

Number of steps:

1 to 255 (per sequence)

Step time:

0.1 ms to 999.9999 s (resolution 0.1 ms or 0.0001 s)

Operations within step: Constant, keep, or linear sweep

Parameter:

DC voltage

Note

, AC voltage

Note

, frequency, waveform, phase (start, end), step

synchronized output (2 bits)

Jump times:

1 to 999 or infinite

Sequence control:

Start:

Starts a sequence.

Stop:

Stops a sequence.

Hold:

Maintains current settings. This is restarted when a

sequence is started.

Branch:

Branches to the specified step.

Note

The setting ranges for AC voltage and DC voltage are determined by the output voltage ranges

set when editing the sequence data.

Sequence control cannot be executed when the output is off.

Содержание EC1000SA




























































































































































































































































































Результаты поиска

Содержание EC1000SA

Отзывы:

Похожие инструкции для EC1000SA

Бренды по названию

Популярные бренды

NF EC1000SA, Инструкция по эксплуатации

Результаты поиска

Содержание EC1000SA

Отзывы:

Похожие инструкции для EC1000SA

Бренды по названию

Популярные бренды