NF EC1000SA Скачать руководство пользователя

Страница: 145 / 283

5.3

SET Menu

EC1000SA

5-15

5.3.1 Output mode setting

Table5-12

lists the eight output modes that can be selected (based on combinations of two operation

modes and four signal source modes).

The mode cannot be changed when output is on. Turn output off before entering settings.

Table5-12. Output Modes

Operation Mode

Signal Source Mode

Output Mode

AC (alternate current)

INT (internal)

AC-INT

EXT (external)

AC-EXT

ADD (in external)

AC-ADD

SYNC (external synchronization)

AC-SYNC

AC+DC
(direct current)

INT (internal)

AC+DC-INT

EXT (external)

AC+DC-EXT

ADD (in external)

AC+DC-ADD

SYNC (external synchronization)

AC+DC-SYNC

a) Selection of operation mode

The EC1000SA enables selection between two operation modes: AC (alternate current) and AC+DC

(direct current).

•

AC:

In this mode, the EC1000SA is used as an AC constant-voltage source. The voltage

supplied to the load is the set value or proportionate to the input signal. The DC

component is removed.

•

AC+DC: In this mode, the EC1000SA is used as a DC constant-voltage source. The voltage

supplied to the load is the set value or proportionate to the input signal.

b) Selection of signal source

The EC1000SA enables selection of four signal source modes: INT (internal), EXT (external), ADD

(in external), and SYNC (external synchronization).

•

INT:

The EC1000SA internal signal source is used. DC or AC set via the control panel menu is

output.

•

EXT:

Signals from an external signal that is connected to the external signal input/external sync

signal input terminal (EXT SIG IN/EXT SYNC IN) on the rear panel are output as external

input gain amplified signals.

•

ADD:

In this mode, a waveform comprised of the above INT and EXT signal sources is output.

•

SYNC: In this mode, the output waveform is synchronized with either an external sync signal

source (TTL) connected to the external signal input/external sync signal input terminal

(EXT SIG IN/EXT SYNC IN) on the rear panel or the input power line.

Содержание EC1000SA




























































































































































































































































































Результаты поиска

Содержание EC1000SA

Отзывы:

Похожие инструкции для EC1000SA

Бренды по названию

Популярные бренды

NF EC1000SA, Инструкция по эксплуатации

Результаты поиска

Содержание EC1000SA

Отзывы:

Похожие инструкции для EC1000SA

Бренды по названию

Популярные бренды