MR VACUTAP VV Скачать руководство пользователя страница 60

Страница: 60 / 198

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

4349322/01 EN

VACUTAP

3. Temporarily fasten on-load tap-changer to supporting structure. The sup-

porting flange has through holes for this purpose.

Figure 43: Temporary fastening

5.3.2 Connecting the tap winding and on-load tap-changer take-off

lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads which place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer!

► Establish and secure connections with care.

► Do not twist connection contacts.

► Connect connecting leads without warping or deforming.

► If necessary use an expansion loop for connecting leads.

1. Connect tap winding and on-load tap-changer take-off lead in accordance

with the connection diagram included with the delivery.

2. If connection leads have to cross the open surface of the oil compartment/

change-over selector, there must be a clearance of 50 mm between the
connecting leads and the surface of the oil compartment/change-over se-
lector.

The designations of the on-load tap-changer's connection contacts are
shown in the connection diagram. The connection contacts are provided with
vertical through-holes (11 mm diameter for M10 screws, see appendix).

Содержание VACUTAP VV







































































































































































































Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды

MR VACUTAP VV, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды