MR VACUTAP VV Скачать руководство пользователя страница 14

Страница: 14 / 198

2 Safety

Maschinenfabrik Reinhausen GmbH 2020

4349322/01 EN

VACUTAP

▪ It is imperative that you consult with Maschinenfabrik Reinhausen GmbH

because specific operating conditions apply to alternative insulating fluids.

▪ Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

▪ Only use lubricants and auxiliary materials approved by the manufacturer.

▪ Contact the manufacturer.

Modifications and conversions

Unauthorized or inappropriate changes to the product may lead to personal
injury, material damage and operational faults.

▪ Only modify the product after consultation with Maschinenfabrik Rein-

hausen GmbH.

Spare parts

Spare parts not approved by Maschinenfabrik Reinhausen GmbH may lead
to physical injury, damage to the product and malfunctions.

▪ Only use spare parts that have been approved by Maschinenfabrik Rein-

hausen GmbH.

▪ Contact Maschinenfabrik Reinhausen GmbH.

2.4 Personal protective equipment

Personal protective equipment must be worn during work to minimize risks to
health.

▪ Always wear the personal protective equipment required for the job at

hand.

▪ Never wear damaged personal protective equipment.

▪ Observe information about personal protective equipment provided in the

work area.

Protective clothing

Close-fitting work clothing with a low tearing strength,
with tight sleeves and with no protruding parts. It mainly
serves to protect the wearer against being caught by
moving machine parts.

Safety shoes

To protect against falling heavy objects and slipping on
slippery surfaces.

Safety glasses

To protect the eyes from flying parts and splashing liq-
uids.

Visor

To protect the face from flying parts and splashing liq-
uids or other dangerous substances.

Hard hat

To protect against falling and flying parts and materials.

Hearing protection

To protect against hearing damage.

Protective gloves

To protect against mechanical, thermal, and electrical
hazards.

Table 3: Personal protective equipment

Содержание VACUTAP VV







































































































































































































Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды

MR VACUTAP VV, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды