MR VACUTAP VV Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 198

background image

7 Fault elimination

Maschinenfabrik Reinhausen GmbH 2020

173

4349322/01 EN

VACUTAP

®

VV

®

7.2 Tripping the pressure monitoring device and putting the

transformer back into operation

WARNING

Danger of death or severe injury!

Danger of severe injury or death if on-load tap-changer and transformer are
insufficiently tested.

► Be sure to contact Maschinenfabrik Reinhausen to check on-load tap-

changer and transformer after the pressure monitoring device has been
tripped.

► Only use the equipment again when you are sure there is no damage to

the on-load tap-changer or transformer.

If the circuit breaker is tripped by the pressure monitoring device, proceed as
follows:

1. Establish time of tripping.

2. Determine operating position of on-load tap-changer.

3. As a precaution, block the motor-drive unit by tripping the motor protective

switch to prevent the on-load tap-changer from being actuated by remote
control.

4. Check the on-load tap-changer head cover. If insulating fluid is leaking,

close the oil conservator stop valve immediately.

5. Check whether the pressure monitoring device sensor is in the OFF posi-

tion or OPERATION position.

7.2.1 Sensor in the OPERATION position

If the sensor is in the OPERATION position, there may be an error in the trip-
ping circuit. Check the tripping circuit in this case. If you are not able to clar-
ify why the pressure monitoring device tripped, be sure to contact Maschi-
nenfabrik Reinhausen to check the on-load tap-changer.

7.2.2 Sensor in the OFF position

Proceed as follows if the sensor is in the OFF position.

1. Ensure that the transformer is not started up under any circumstances.

«
...
171
172
173
174
175
...
»

Содержание VACUTAP VV







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VV

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: Kawai Страницы: 10

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: FabiaTech Страницы: 2

Бренд: FabiaTech Страницы: 77

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: IDEAL Networks Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды