MR VACUTAP VV Скачать руководство пользователя страница 38

Страница: 38 / 198

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

4349322/01 EN

VACUTAP

5.2.1.1 Lifting top part of on-load tap-changer head off supporting flange

(bottom part)

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

CAUTION!

An unstably positioned on-load tap-changer may tip, re-

sulting in serious injuries and damage. Place on-load tap-changer on a
level surface and secure it against tipping.

2. Remove red-colored packaging material and transport material from on-

load tap-changer.

3. Ensure that the on-load tap-changer is in the adjustment position. The ad-

justment position is indicated in the on-load tap-changer connection dia-
gram included in delivery.

4. Ensure that the inspection window is sealed off with the cover.

5. Remove screws and locking washers on on-load tap-changer head cover.

Figure 18: On-load tap-changer head cover

Содержание VACUTAP VV







































































































































































































Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды

MR VACUTAP VV, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды