MR VACUTAP VV Скачать руководство пользователя страница 159

Страница: 159 / 198

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

159

4349322/01 EN

VACUTAP

▪ Remove leads used for testing before the high voltage test as these func-

tion as antennas.

▪ Wherever possible, route the measurement leads and data leads sepa-

rately to the energy cables.

Contact the manufacturer if you have any questions about possible sources
of danger.

6.2 Transporting transformer to the operating site

NOTICE

Damage to motor-drive unit!

Damage to the motor-drive unit due to condensate in protective housing of
motor-drive unit.

► Always keep protective housing of the motor-drive unit tightly closed.

► In the event of downtime lasting more than 8 weeks prior to initial com-

missioning, connect and operate the anti-condensation heater in the mo-
tor-drive unit. If this is not possible, place a sufficient amount of desiccant
in the protective housing.

6.2.1 Transport with drive removed

1. Ensure that the drive and the on-load tap-changer are in the adjustment

position.

2. Remove the drive.

3. Do not actuate the drive while the on-load tap-changer is uncoupled and

do not turn the output shaft.

4. Do not actuate an on-load tap-changer which is uncoupled and do not turn

its drive shaft.

5. Transport the drive to the installation site in the MR delivery packaging.

6. Fit the drive [

►

Section 5.4.5, Page 99] and the drive shaft [

►

Section

5.4.6, Page 99] to the transformer at the installation site.

Содержание VACUTAP VV







































































































































































































Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды

MR VACUTAP VV, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды