MR VACUTAP VV Скачать руководство пользователя страница 161

Страница: 161 / 198

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

161

4349322/01 EN

VACUTAP

3. Discharge the gas from under the on-load tap-changer cover. Ensure suf-

ficient fresh air (e.g. in transformer cells and work tents) when doing so.

4. Once the gas has been discharged and the insulating fluid is flowing out

of the air-vent valve, close the air-vent valve and close the stop-cock be-
tween the oil conservator and oil compartment.

5. Open air-vent valve again and drain off approximately 5–10 liters of insu-

lating fluid via the pipe connection S until the area under the on-load tap-
changer head cover is free of insulating fluid.

6. Loosen 24 screws M10 / wrench size 17 with locking elements on the on-

load tap-changer head cover.

7. Remove on-load tap-changer head cover.

8. Extract insulating fluid via pipe connection S.

9. Open stop-cock between oil conservator and oil compartment.

Insulating fluid flows out of the oil conservator into the oil compartment.

10. Extract insulating fluid via pipe connection S.

11. Place on-load tap-changer head cover on the on-load tap-changer head.

12. Screw down on-load tap-changer head cover using 24 screws M10 /

wrench size 17 and locking elements (tightening torque 34 Nm).

6.2.3.2 Emptying oil compartment without oil suction pipe

WARNING

Danger of explosion!

Explosive gases under the on-load tap-changer head cover can deflagrate
or explode and result in severe injury or death.

► Ensure that there are no ignition sources such as open flames, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the imme-
diate surroundings and that none occur.

► De-energize all auxiliary circuits (for example tap-change supervisory de-

vice, pressure relief device, pressure monitoring device) before removing
the on-load tap-changer head cover.

► Do not operate any electrical devices during the work (e.g. risk of sparks

from impact wrench).

1. De-energize all auxiliary circuits (for example the tap-change supervisory

control, pressure relief device, pressure-operated relays).

2. If the stop-cock (slide valve) between the oil conservator and oil compart-

ment is open, open the air-vent valve E1 on the on-load tap-changer
head.

3. Drain off the gas from under the on-load tap-changer cover. Ensure suffi-

cient fresh air (for example in transformer cells and work tents).

4. Once the gas has been drained off and the oil is flowing out of the air-vent

valve, close this valve and close the stop-cock between the oil conserva-
tor and oil compartment.

Содержание VACUTAP VV







































































































































































































Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды

MR VACUTAP VV, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VV

Отзывы:

Похожие инструкции для VACUTAP VV

Бренды по названию

Популярные бренды