manualshive.com logo in svg

Motorola MPC860 PowerQUICC, Руководство пользователя

"Motorola MPC860 PowerQUICC" - отличный продукт для тех, кто ищет высококачественный процессор. У нас вы можете найти бесплатное руководство пользователя. Скачайте его с нашего сайта и руководствуйтесь руководством для оптимальной производительности и эффективности. manualshive.com - ваш источник полезной информации для вашего продукта.

Поделиться
Скачать
background image

MOTOROLA

Chapter  31.  Serial Peripheral Interface

  

31-11

Part V. The Communications Processor Module

Table 31-4 describes the SPCOM Þelds.

31.5  SPI Parameter RAM

The SPI parameter RAM area begins at the SPI base address. It is similar to the SCC
general-purpose parameter RAM. Some values must be user-initialized before the SPI is
enabled; the CPM initializes the others. Once initialized, parameter RAM values do not
usually need to be accessed. They should be changed only when the SPI is inactive.
Table 31-5 shows the memory map of the SPI parameter RAM.

Table 31-4. SPCOM Field Descriptions 

Bits

Name

Description

0

STR

Start transmit. For an SPI master, setting STR causes the SPI to start transferring data to and from the 
Tx/Rx buffers if they are prepared. For a slave, setting STR when the SPI is idle causes it to load the Tx 
data register from the SPI Tx buffer and start sending with the next SPICLK after SPISEL is asserted. 
STR is cleared automatically after one system clock cycle.

1Ð7

Ñ

Reserved and should be cleared.

Table 31-5. SPI Parameter RAM Memory Map 

Offset 

1

Name

Width

Description

0x00

RBASE

Hword Rx/Tx BD table base address. Indicate where the BD tables begin in the dual-port RAM. 

Setting Rx/TxBD[W] in the last BD in each BD table determines how many BDs are 
allocated for the Tx and Rx sections of the SPI. Initialize RBASE/TBASE before enabling 
the SPI. Furthermore, do not conÞgure BD tables of the SPI to overlap any other active 
controllerÕs parameter RAM.
RBASE and TBASE should be divisible by eight.

0x02

TBASE

Hword

0x04

RFCR

Byte

Rx/Tx function code. Contains the value to appear on AT[1-3] when the associated 
SDMA channel accesses memory. Also controls byte ordering for the transfers. See 
Section 31.5.1, ÒReceive/Transmit Function Code Registers (RFCR/TFCR).Ó

0x05

TFCR

Byte

0x06

MRBLR

Hword Maximum receive buffer length. The SPI has one MRBLR entry to deÞne the maximum 

number of bytes the MPC860 writes to a Rx buffer before moving to the next buffer. The 
MPC860 can write fewer bytes than MRBLR if an error or end-of-frame occurs, but never 
exceeds the MRBLR value. User-supplied buffers should be no smaller than MRBLR.
Tx buffers are unaffected by MRBLR and can have varying lengths; the number of bytes 
to be sent is programmed in TxBD[Data Length].

MRBLR is not intended to be changed while the SPI is operating. However it can be 
changed in a single bus cycle with one 16-bit move (not two 8-bit bus cycles 
back-to-back). The change takes effect when the CPM moves control to the next RxBD. 
To guarantee the exact RxBD on which the change occurs, change MRBLR only while 
the SPI receiver is disabled. MRBLR should be greater than zero; it should be an even 
number if the character length of the data exceeds 8 bits.

0x08

RSTATE Word

Rx internal state. Reserved for CPM use.

0x0C

Ñ

Word

The Rx internal data pointer 

2

 is updated by the SDMA channels to show the next 

address in the buffer to be accessed. 

0x10

RBPTR

Hword  RxBD pointer. Points to the current Rx BD being processed or to the next BD to be 

serviced when idle. After a reset or when the end of the BD table is reached, the CPM 
initializes RBPTR to the RBASE value. Most applications should not modify RBPTR, but 
it can be updated when the receiver is disabled or when no Rx buffer is in use.

Содержание MPC860 PowerQUICC



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC860 PowerQUICC

ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Бренд: ECKELMANN Страницы: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Бренд: H3C Страницы: 17
H3C WX Series Getting Started Manual preview
WX Series
Бренд: H3C Страницы: 32
Jetter 60873050 Manual preview
60873050
Бренд: Jetter Страницы: 24
Eaton Cutler-Hammer Jockey Instructions Manual preview
Cutler-Hammer Jockey
Бренд: Eaton Страницы: 12
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Бренд: WAC Страницы: 5
Auber WS-1500FXL Operation & Instruction Manual preview
WS-1500FXL
Бренд: Auber Страницы: 3
Danfoss VLTAutomationDrive FC 360 Quick Manual preview
VLTAutomationDrive FC 360
Бренд: Danfoss Страницы: 52
Sonos Controller CR100 Brochure & Specs preview
Controller CR100
Бренд: Sonos Страницы: 2
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Бренд: zeeltronic Страницы: 15
M-system M8BS2-081 Instruction Manual preview
M8BS2-081
Бренд: M-system Страницы: 3
Melexis DVK90121 User Manual preview
DVK90121
Бренд: Melexis Страницы: 13
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Бренд: OCL Страницы: 2
OBO Bettermann C50-0-255 Installation Instructions Manual preview
C50-0-255
Бренд: OBO Bettermann Страницы: 6
Digital Acoustics IP7-MZC-FD Application Manual preview
IP7-MZC-FD
Бренд: Digital Acoustics Страницы: 7
Walchem W600 Series Instruction Manual preview
W600 Series
Бренд: Walchem Страницы: 88
Atmel AVR128 Application Note preview
AVR128
Бренд: Atmel Страницы: 8
Evco EVRS225 Manual preview
EVRS225
Бренд: Evco Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды