MTS 2 and MTS 4 Installation, Con
fi
guration and Basic Service Manual
Con
fi
guring Redundant Site Controller
Process 8-7
How to Configure Redundant Site Controllers
1
Perform Site Controller Hardware Pre-Checks, as described in
Procedure 8-26, "Site Controller
Hardware Pre-Checks," on page 8-47
.
2
Con
fi
gure the Site Controller Con
fi
guration Files, see
Procedure 8-27, "Site Controller
3
Con
fi
gure Ethernet ports connecting the two Site Controllers, as described in
gure Ethernet Ports," on page 8-48
4
Con
fi
gure the ID values of the Site Controllers, see
.
Procedure 8-26
Site Controller Hardware Pre-Checks
1
Ensure that both SCs are correctly installed and are running identical software applications,
Boot images and con
fi
guration
fi
les.
2
In order for the Redundant Site Controller feature to work correctly, the Site Controller and
BR Boot1 version must be:
•
TSC_RLJ_BOOT1–R06.40.07 or later for Site Controller.
•
BRC_RLJ_BOOT1–R06.40.05 or later for Base Radio.
The Boot1 version can be checked on the Site Controller and BRs by using the
ver
command on both the Site Controller and on the Base Radio.
3
Check that the redundant Site Controller Ethernet Link cables are connected correctly, as shown
in Figure 5–6.
4
Proceed to
below.
Procedure 8-27
Site Controller Configuration Files
In order to check that the Site Controller con
fi
guration
fi
les have the Standby Site
Controller Installed parameter enabled, follow the steps below.
1
Log onto the Site Controller Application MMI.
2
From the SC: prompt, run the command
display config
.
3
Check the output of the con
fi
guration and con
fi
rm if the Standby SC parameter is enabled or not.
4
If no Standby Site Controller is enabled, upload the Active Site Controller con
fi
guration
fi
le.
5
Modify the con
fi
guration
fi
le in TESS to enable Standby Site Controller.
6
Download the new con
fi
guration
fi
le to the InActive Bank (set to use as next after reset).
7
Reset the Site Controller.
8
Con
fi
rm the con
fi
guration is correct.
6802800U74-N September 2009
8-47
Содержание DIMETRA MTS 2
