Mercury 2010 Milan Скачать руководство пользователя страница 288 | Manualshive

Страница: 288 / 330

background image

3. Step back while the pressure releases.

4. When you are sure that all the pressure has been released, use the
cloth to turn it counterclockwise and remove the cap.

•

2.5L coolant bleed valve

•

3.0L coolant bleed valve

5. Open the coolant bleed valve on the back of the engine water outlet
for the 2.5L engine or in the thermostat housing for the 3.0L engine.

6. Fill the coolant reservoir slowly with the proper coolant mixture, to
within the COLD FILL RANGE or the FULL COLD level on the reservoir.
If you removed the radiator cap in an overflow system, fill the radiator
until the coolant is visible and radiator is almost full.

7. Close the bleed valve and reinstall the cap on the coolant reservoir.
Turn the cap until it is tightly installed to prevent coolant loss.

After any coolant has been added, check the coolant concentration (refer
to

Checking engine coolant).

If the concentration is not 50/50

(protection to –34°F/–36°C), drain some coolant and adjust the
concentration. It may take several drains and additions to obtain a 50/50
coolant concentration.

Maintenance and Specifications

288

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
286
287
288
289
290
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: iDataLink Страницы: 106

WirelessAIR 73000EZ

Бренд: Air Lift Страницы: 12

10-8002-C11670C

Бренд: Saleen Страницы: 17

1506-PHX Cargo Plus

Бренд: Ranger design Страницы: 8

Бренд: AUTOTECH Страницы: 1

2005 JR41 Stratus

Бренд: Dodge Страницы: 293

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

Бренд: Whispbar Страницы: 63

Бренд: Toyota Страницы: 285

Бренд: Acura Страницы: 4

Бренд: Brodit Страницы: 2

viano 639 series

Бренд: Mercedes-Benz Страницы: 32

Бренд: Hamron Страницы: 6

Camry Hybrid 2012

Бренд: Toyota Страницы: 62

Бренд: Ford Страницы: 10

Бренд: Fiat Страницы: 204

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды