Mercury 2010 Milan Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 330

background image

WARNING:

Do not attempt to service, repair, or modify the

airbag SRS, its fuses or the seat cover on a seat containing an

airbag. Contact your authorized dealer as soon as possible.

WARNING:

All occupants of the vehicle should always wear

their safety belts even when an airbag SRS is provided.

How does the side airbag system work?

The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags (including side air
curtain systems).

The side airbag system consists of
the following:

•

An inflatable bag (airbag) with a
gas generator concealed behind
the outboard bolster of the driver
and front passenger seatbacks.

•

The same warning light,
electronic control and diagnostic
unit as used for the front airbags.

•

Two crash sensors located under
the outboard side of the front seats, attached near the floor.

Side airbags, in combination with safety belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.

The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. The airbag was designed to inflate between
the door panel and occupant to further enhance the protection provided
occupants in side impact collisions.

The airbag SRS is designed to activate when the vehicle sustains lateral
deceleration sufficient to cause the sensors to close an electrical circuit
that initiates airbag inflation.

Seating and Safety Restraints

142

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
140
141
142
143
144
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Samsung Страницы: 133

Бренд: Uebler Страницы: 18

Бренд: Ford Страницы: 52

Бренд: Thule Страницы: 8

Бренд: Maserati Страницы: 210

Бренд: OnStar Страницы: 22

Бренд: GMC Страницы: 120

Бренд: Prime Tech Страницы: 6

Бренд: Hyundai Страницы: 11

Бренд: Audiovox Страницы: 3

Бренд: Victory 4x4 Страницы: 9

Бренд: Lund Страницы: 12

Бренд: Westin Страницы: 3

Бренд: Xforce Страницы: 11

Бренд: Volkswagen Zubehör Страницы: 133

Бренд: Ford Страницы: 2

Бренд: Toyota Страницы: 596

Бренд: Chevrolet Страницы: 376

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды