Mercury 2010 Milan Скачать руководство пользователя страница 246

Страница: 246 / 330

Stopping and securing the vehicle

1. Park on a level surface, set the parking brake and activate the hazard
flashers.

2. Place the gearshift lever in P (Park) (automatic transmission) or R
(Reverse) (manual transmission) and turn the engine off.

Removing the spare tire and jack

1. Remove the carpeted load floor
panel located in the rear of the
vehicle and remove the lug wrench
and long bolt from the tool bag.

2. Remove the bolt securing the
spare tire using the lug wrench,
then lift and remove the spare tire
from the trunk.

3. Remove the jack retention bolt by
turning it counterclockwise and
remove the jack from the vehicle.

Tire change procedure

WARNING:

To help prevent the vehicle from moving when you

change a tire, be sure the parking brake is set, then block (in

both directions) the wheel that is diagonally opposite (other side and
end of the vehicle) to the tire being changed.

WARNING:

If the vehicle slips off the jack, you or someone else

could be seriously injured.

Roadside Emergencies

246

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды