Mercury 2010 Milan Скачать руководство пользователя страница 283 | Manualshive

Страница: 283 / 330

background image

BATTERY

Your vehicle is equipped with a
Motorcraft

威

maintenance-free

battery which normally does not
require additional water during its
life of service.

If your battery has a
cover/shield, make sure it is
reinstalled after the battery has
been cleaned or replaced.

For longer, trouble-free operation,
keep the top of the battery clean and dry. Also, make certain the battery
cables are always tightly fastened to the battery terminals.

If you see any corrosion on the battery or terminals, remove the cables
from the terminals and clean with a wire brush. You can neutralize the
acid with a solution of baking soda and water.

It is recommended that the negative battery cable terminal be
disconnected from the battery if you plan to store your vehicle for an
extended period of time. This will minimize the discharge of your battery
during storage.

Note: Electrical or electronic accessories or components added to
the vehicle by the dealer or the owner may adversely affect
battery performance and durability.

WARNING:

Batteries normally produce explosive gases which

can cause personal injury. Therefore, do not allow flames, sparks

or lighted substances to come near the battery. When working near the
battery, always shield your face and protect your eyes. Always provide
proper ventilation.

WARNING:

When lifting a plastic-cased battery, excessive

pressure on the end walls could cause acid to flow through the

vent caps, resulting in personal injury and/or damage to the vehicle or
battery. Lift the battery with a battery carrier or with your hands on
opposite corners.

Maintenance and Specifications

283

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
281
282
283
284
285
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 14

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

Бренд: IBASE Technology Страницы: 100

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

MagicWatch MWE250

Бренд: Waeco Страницы: 172

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: TATA Motors Страницы: 151

QUICKDRAW RACHET TIE-DOWNS 855

Бренд: Thule Страницы: 3

Charger SRT 392 2017

Бренд: Dodge Страницы: 576

Бренд: Lexus Страницы: 108

Бренд: Seat Страницы: 300

Бренд: Lexus Страницы: 6

Бренд: Audiovox Electronics Страницы: 12

Бренд: Metra Electronics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды